Get NACE-CIP2-001 Actual Free Exam Q&As to Prepare for Your NACE Certification
NACE Actual Free Exam Questions And Answers
The Coating Inspector Level 2 certification is considered to be one of the most prestigious certifications in the coatings industry. It is intended for individuals who have a minimum of two years of experience in the coatings industry and have completed the Coating Inspector Level 1 certification. The Level 2 certification exam covers a wide range of topics, including surface preparation, coating application, quality control, and inspection techniques.
To qualify for the NACE-CIP2-001 Certification Exam, candidates must have at least two years of experience in the coatings industry and have successfully completed the Coating Inspector Level 1 exam. The Level 2 exam covers a wide range of topics, including surface preparation, coating application, coating systems, inspection techniques, and safety. NACE-CIP2-001 exam consists of both a written and practical component, and passing both components is required to achieve certification.
NEW QUESTION # 43
You should bulk store coatings containing isocyanates
- A. in a heated warehouse.
- B. in a well ventilated area separate from the work place.
- C. in a refrigerated warehouses
- D. wherever it is convenient
Answer: B
NEW QUESTION # 44
Antifouling coatings are regulated by international treaties.
- A. False
- B. True
Answer: B
NEW QUESTION # 45
You are the NACY Coating Inspector on a tank lining project where desiccant dehumidification is being used. Since the first shift of abrasive blasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Check to See if the dehumidification equipment is operating correctly
- C. Document the readings at the end of the shift
- D. Advise the coating applicator supervisor of your readings
Answer: D
NEW QUESTION # 46
You are the NACE Inspector on a project where a stationary floating structure is being coated and you notice a self-smoothing anti-fouling coating has been specified.
This is not a good choice because:
- A. The floating structure is stationary
- B. It will result in a very slippery surface
- C. It contains biocide
- D. It doesn't contain biocide
Answer: C
NEW QUESTION # 47
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Use a generally accepted industry standard and to take readings
- C. Develop your own methodology and proceed take the readings
- D. Refuse to take readings until an is in place
Answer: B
NEW QUESTION # 48
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Cure stage
- B. Flow stage
- C. Wetting stage
- D. Gel stage
Answer: B
NEW QUESTION # 49
From a corrosion perspective, the main difference between Ferrous and Non-Ferrous Metals is:
- A. Iron content
- B. Safety
- C. Appearance
- D. Cost
Answer: A
NEW QUESTION # 50
You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value.
As this is not part of the standard you should:
- A. Call your supervisor
- B. Ignore the additional requirement
- C. Enforce the additional requirement
- D. Request clarification from the specifier
Answer: C
NEW QUESTION # 51
A failure caused by applying a coating too thinly is known as
- A. chalking.
- B. cracking.
- C. failure to cure.
- D. pinholes.
Answer: D
NEW QUESTION # 52
The Concrete Repair Institute's comparators can be used to assess:
- A. Contamination levels prior to coating
- B. Surface profile prior to coating
- C. Compressive and tensile strength prior to coating
- D. Surface cleanliness prior to coating
Answer: B
NEW QUESTION # 53
Cold-applied tape
- A. are identifiable by its distinct colors, usually light blue, green, Or Grey.
- B. have a cross-linked polyethylene backing and a heat-activated adhesive.
- C. is polyethylene film, heat laminated, 'With an adhesive layer of butyl glue.
- D. is typically green or led and looks like "painted" finish.
Answer: C
NEW QUESTION # 54
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Advise the Owner and write a Non-Conformance report
- B. Ignore the situation
- C. Stop the job
- D. Require the Applicator to remove the coating
Answer: D
NEW QUESTION # 55
Non-Conformance Reports are designed to:
- A. To identify items that do not meet the specification requirements
- B. Assist the Owner in negotiating credits from the Contractor
- C. Elevate the status of the Inspector
- D. Punish the Contractor for substandard work
Answer: A
NEW QUESTION # 56
When observing design defects the NACE Inspector should:
- A. Request that the item be rebuilt with a better design for coating
- B. Stop the job immediately
- C. Document the defect and the potential problems that could result
- D. Ignore the defect as the inspector can't change the design
Answer: C
NEW QUESTION # 57
Coating application to concrete substrates is:
- A. The same as coating steel
- B. More challenging than coating steel
- C. Less challenging, than coating steel
- D. Not required as Concrete is inorganic
Answer: B
NEW QUESTION # 58
NACE Level 2 Inspectors have been authorized to perform:
- A. Visual inspection and Non-destructive testing
- B. Visual inspection, Non-Destructive and Destructive testing
- C. All types of inspection without supervision
- D. Visual inspection only
Answer: B
NEW QUESTION # 59
Examples of non-ferrous metals include
Select All that Apply:
- A. copper
- B. mild steel.
- C. aluminum
- D. iron
Answer: A,C
NEW QUESTION # 60
You are working as an inspector in a galvanizing plant for the first time.
What are some of the hazards you need to be aware of:
- A. Risk of skin
- B. Risk of acid or caustic splashes
- C. a), b), and c)
- D. Risk of chemical exposure
Answer: C
NEW QUESTION # 61
......
NACE-CIP2-001 Questions Truly Valid For Your NACE Exam: https://examcompass.topexamcollection.com/NACE-CIP2-001-vce-collection.html
